Conettix D6600 Installation Guide download pdf (Page 6)

D6600 | System Guide | 3.0 Operation

6 Bosch Security Systems, Inc. | 4/10 | 4998122712-04

For the appropriate configuration information for each

device, refer to the following installation guides:

•

C900TTL-E Dialer Capture Module Installation

Guide (P/N: 4998122718)

Conettix C900V2 Dialer Capture Ethernet

Module Installation Guide (P/N: F01U003472)

D9133TTL-E Serial Interface Module Installation

Guide (P/N: 4998122717)

Conettix DX4020 Ethernet Network Interface

Module Installation Guide (P/N: F01U045288)

Conettix D6680 Ethernet Network Adapter

Installation Guide (P/N: 4998138732)

Conettix D6682 Network Ethernet Adapter

Installation Guide (P/N: F01U078049)

Conettix ITS-DX4020-G GPRS/GSM IP

Communicator Module Installation and Operation

Guide (P/N: F01U163066)

2.1 Conettix D6600/D6100i

Pre-Installation Requirements

Consider the following pre-installation requirements

before attempting to install a Conettix D6600/D6100i

Network system. If you have any questions regarding

these items, contact the network administrator for the

network with which you will interface, or a Bosch

network engineer.

For UL Listed Fire Installations, shared

on-premises communications equipment

is required to be UL Listed for Information

Technology Equipment.

2.1.1 Setting Up the Conettix D6600/D6100i over

an Ethernet Network

•

The Ethernet network must use Ethernet cables.

The D6200 host computer must have a properly

configured Ethernet network interface card (NIC)

installed.

The D6600 must be connected to the Ethernet

network using a Bosch D6680/D6682 Network

Adapter or a D6100i must be connected to the

Ethernet network.

All alarm control panels, except Bosch control

panels, used in the Conettix system must use a

Bosch C900V2 or C900TTL-E.

Bosch control panels used in the Conettix system

should use a Bosch DX4020 Network Interface

Module or a D9133TTL-E Network Interface

Module.

2.1.2 Host Computer for Conettix D6600/D6100i

System Setup

The host computer uses the ARP and TELNET

DOS commands to configure the D6680/D6682,

D6100i, D9133TTL-E or DX4020, or

C900V2/C900TTL-E. The D6200 software can be

used instead of the ARP and TELNET

commands. Refer to the D6200 Software

Operation and Installation Guide

(P/N: 4998154991) and the appropriate network

device installation guide.

The host computer must have a properly

configured Ethernet network interface card (NIC)

installed.

The host computer must have the appropriate

Ethernet cable. Manually set the host computer's

IP address to an address that is acceptable to the

particular class of the network (refer to

Section

3.1 Setting Up the Host Computer,

page

6).

3.0 Operation

3.1 Setting Up the Host Computer

If the computer you plan to use for

programming the D6600, the D6100i, the

D6680/D6682, and the alarm panel

network adapters is already a functioning

workstation within the network you are

planning to utilize, proceed to Section 3.2

Network Failover Solution

(D6600 Only) on page 9.

The host computer is any computer or workstation

that is connected to the network you will use to

manage/administer the D6600/D6100i and other

devices. Any existing laptop or desktop computer on

the network can be used. However, for security

reasons, it is best that the computer not be used as a

regular workstation. This computer is also the

computer on which you install the D6200 Software.

The D6200 Software is used to program and

administer the D6600/D6100i and other devices.

Separate sections are provided for setting up the host

computer in Windows 2000, XP, Vista, and

Windows 7.

1 2 3 4 5 6 7 8 9 10 11 ... 19 20

Comments to this Manuals

No comments

Conettix D6600 Installation Guide Page 6

Comments to this Manuals

Related products and manuals for Gateways/controllers Conettix D6600